Note: if two cans of solder paste need to be stirred at the same time, it is necessary to confirm that the weight is approximately equal and the difference is not more than 50g. If only one can of solder paste needs to be stirred at a time, a 500g balance weight shall be selected according to the weight of the solder paste or an empty solder paste tank shall be filled with a scrap solder paste or other articles of equivalent weight as the balance weight. To stop the machine during operation, press the power on key to stop and cancel the operation. When the upper cover of the machine is opened during operation, the machine will stop automatically. After the upper cover is closed, it is not necessary to press the power switch again to continue the mixing operation.
The solder paste mixer is a precise mechanical equipment. Regular maintenance will prolong its service life.
1. The machine uses fully enclosed bearings, and the inside of the machine needs to be kept clean.
2. The belt of the rotation device is not a durable product. If it is damaged, it should be replaced in time.
1. It is strictly prohibited to open the machine cover or the mixing operation when the machine cover is not locked. If you want to open the upper cover of the machine after production and operation, you must wait until the machine is completely stopped before opening it.
2. The machine will tremble when moving, so the machine should be placed in a stable and solid place. In case of excessive and violent vibration during the operation of the machine, the power supply should be turned off immediately. After all parts of the machine stop running, the cover should be opened for inspection and troubleshooting.
ARAMETER ? Equipment parameters
Working voltage: AC220V (60Hz) 40W
Operating speed: primary operation: 1400rpm secondary operation: 400rpm
Machine size: 410 * 410 * 490mm (w.d.h)
Net / gross weight: 40kg / 45kg
Time setting: 0.1-9.9 minutes, 0.1 minutes for each adjustment, 10-30 minutes for each adjustment, and 1.0 minutes for each adjustment. The solder paste mixer generates centrifugal force by revolution, and cooperates with the force generated by the rotation at an angle of 45 degrees with the axis of revolution, so that the solder paste at the upper end of the tank moves continuously downward, while the solder paste at the bottom of the pipe moves from the surrounding to the tank, forming a cyclone funnel-shaped mixing action, which can smoothly stir and soften the solder paste After defoaming and reaching proper viscosity, the solder paste has good wettability, uniform diffusivity and excellent
The printing effect can achieve the best welding performance during reflow. Its characteristics are as follows:
1. It is not necessary to deice the solder paste before mixing.
2. Special control circuit, adjustable mixing time and speed, convenient operation.
3. The solder paste is placed at 45 degrees and rotates along the axis direction. The solder paste will not adhere to the can cover.
4. Stable operation, low noise, natural temperature return and bubble removal during mixing.
5. The solder paste tank does not need to be opened, and it is convenient and safe to take and place. The clamp is suitable for all kinds of solder paste tanks.
6. No moisture problem, no damage to the shape of tin powder.
7. The single power supply is 220V, with safety device to ensure personal safety.
INSTALLATION ? Installation and commissioning
1. Remove the package and carefully read the manual. Lift the main engine with both hands at the bottom of the main engine, place the main engine in the correct direction, and the ground shall be solid and stable.
2. Please check that the voltage specification (AC220V) of the machine is consistent with the voltage specification of the mains.
3. Open the lock catch, lift the upper cover of the machine, rotate the revolving running device clockwise by hand, and at the same time, the clamp of the solder paste tank should make corresponding rotation movement.
4. Confirm that the power supply is correct and the power switch is at the off / off position, and turn on the power supply.
5. Adjust the panel time to a better mixing time depending on the solder paste quality and refrigeration condition
6. To stop the machine during operation, press the power on key to stop and cancel the operation.
OPERATION ? Operation steps:
